This Safety Notice affects All Original Ozium Harnesses (not the new Ozium 2).

We have had reported a case of failure during a simulated tyrolean deployment. The pins on the reserve deployment handles of all original Ozium harnesses may have been damaged during production. The damage, if present, may result in the pin breaking during deployment causing the reserve compartment to remain closed even if the handle is released. As the breakage is in an area hidden from view we are replacing all reserve handles as a precautionary measure.

Action required : Mandatory Replacement of Reserve Handle.

The reserve deployment handles on all Original Ozium harnesses should be replaced before next use. Please contact the dealer who sold you your Ozium harness to request a replacement handle. Replacement (GOOD) handles are clearly marked with blue bartacks. If your reserve handle has the blue bartacks, it has been replaced and is ok to fly. If the reserve handle does not, then it must be replaced. Please see photos at right.

For any questions regarding the replacement of the handle, please contact your local OZONE Dealer or Contact Ozone directly.

SAFETY ALERT : Supair leaf tolerance

SUPAIR LEAF (standard version) “A” and “C” line settings.
A few LEAF were produced with a slow flying configuration and to the maximum allowed for certification approval tolerance.
Concerned products or affected products : LEAF in all sizes : XS, S, M, and L.
Note : that LEAF-LIGHT is not affected.
Problem description : Parachutal phases were observed on a few manufactured “Leaf” while pulling “Ears” in non-accelerated flight mode - the wing will come out of the parachutal phase as soon as the “Ears” are reopened.
More information here.

SAFETY ALERT : Exoceat harness

This notice affects all Exoceat harnesses manufactured before November, 2017.
We have been made aware of a potential safety issue with the Exoceat reserve handle. If the metal pin becomes fatigued due to repeated bending while packing the harness, there is a possibility that the handle could break during extraction.
Action required : Mandatory replacement of all Exoceat reserve handles.
The reserve deployment handles on all Exoceat harnesses should be replaced before next use. Please contact your dealer to request replacement handles.
The correct replacement handles are coloured red, if your reserve handles are made from transparent plastic then they must be replaced before your next flight.
For any questions regarding the replacement of the handle, please contact your local OZONE Dealer or Contact Ozone directly.

SAFETY ALERT : Charly Carabiner

On 15 November 2016, the faulty assembly of a Quick‐Out carabiner lead to its accidental opening.

The pilot had dismounted both of the Quick‐Out’s release buttons and later re‐installed them in swapped positions.

Click here for more information.

SAFETY ALERT : Accidental opening of the ventral automatic buckles in flight

Unwanted openings with automatic ventral aluminum buckles were observed in flight on some SUPAIR harnesses.

For more infos click here.

SAFETY ALERT : Finsterwalder CLICK-LOCK and T-LOCK buckles in the chest strap

there have been two incidents involving older paraglider harnesses equipped with CLICK-LOCK buckles (HSi10) in the chest strap.
The buckles had opened unintentionally during flight while they were under load.
The hooks of the metal tongue can wear out through the frequent diagonal load changes the chest strap is subject to.
Finsterwalder calls on all owners of harnesses equipped with CLICK-LOCKs (HSi10) or T-LOCKs in the chest strap to determine their buckles’ previous usage time by checking the routine test date.

SAFETY ALERT : Unsheathed upper cascade lines on Ozone Alpina 2

Lines becoming knotted and tangles in flight whilst the glider was flown in big-ears mode with the speedbar being operated.

This incident occured when the lines were dry and in good condition.

Pilots are urged to be vigilant about this issue, and visually check their gliders carefully after using big ears or after recovering from a collapse, especially when in accelerated mode with the speedbar.

Where possible the use of an alternative method to lose height is recommanded.

SAFETY ALERT : Rescue handles from Kortel design

We invite all the pilots to check their rescue handle.

The harness’s models are Karma II and Krashbox Module Kuik II

See more infos in English or French.

SAFETY ALERT : Potential problem on forged rings on the Kolibri harness

Description : A potential failure has been fund on the forged rings used on the Kolibri harness.
It may break under usual load.
There is no major risk because this ring is not used in the main structure of the harness.
In case of breaking, there is only the lumbar setting that is concerned.
Process to follow : Harnesses that can be concerned are those with the following serial numbers :

  • Size SM :
    • A1410-KL-M-10
    • A1410-KL-M-16
    • A1410-KL-M-21
    • A1410-KL-M-23
    • A1410-KL-M-24
    • A1410-KL-M-25
    • A1410-KL-M-28
    • A1410-KL-M-29
  • Size ML :
    • A1410-KL-L-1
    • A1410-KL-L-2
    • A1410-KL-L-3
    • A1410-KL-L-4
    • A1410-KL-L-5
    • A1410-KL-L-7
    • A1410-KL-L-26
    • A1410-KL-L-27

If you are concerned with these serial numbers, please contact Kortel Design at +33(0) or by email at
We will give you the process to follow.

Safety information : Carbon fiber seat plate inspection

  1. What is the purpose of this safety warning ?
    We have noticed that a few pilots have been unknowingly flying with bro- ken or damaged carbon fiber seat plates, due to wear and tear, impacts, etc... Carbon fiber is very abrasive sharp ; it could injure the pilot or abrade/ cut/damage the webbing and overall harness structural integrity.
  2. Which product models could be affected ?
    All harness models equipped or accepting carbon fiber seat plates.
  3. What should I do ?
    Check and inspect carefully your carbon fiber seat plate for damage once every 50 flights or once a year.
    If the seat plate is damage in any way, it must be replaced immediately.
    If the harness webbing is frayed or damaged in any way, it is imperative to contact your local Sup’Air dealer for advice prior using your harness again.


We have recently discovered a potential random manufacturing default in our Kuik II models, it is nothing serious but it is necessary for you to inspect your harness to ensure that everything is in order.
The problem observed is the following :
The lower part of the shoulder strap of the harness is connected to a metal buckle located at the “thighs - back” junction behind a small piece of protective neoprene. This buckle is used to connect two sewn straps.

There is no major security, problem since this strap has a multitude of connections within the harness and even in the case of rupture of this seam there is no risk of the pilot falling out of the harness or of the strap breaking upon the deployment of the emergency parachute.

However, a visual inspection of the seams on both sides of the buckle must be made in order to potentially detect the following situation :
There are 4 seams, but they fray easily and the thread can easily be removed with your fingers.

Recall harnesses GIN Gingo Airlite for inspection

Gin Gliders Inc. recalls the last model Gingo Airlite (released in 2012) to perform a precautionary inspection and check after a few months of use the harness is still consistent with our quality standards.

We ask owners of harness Gingo Airlite (Serial No. which the 3rd and 4th digits are "12". Exp xx12-xxxx) to contact their dealer for a return to a factory inspection.